Discrete Electronics
- 1Amp 1200V Max
- High conductivity, avialable in through-hole
- 2 pin through hole rectifier diodes used for many electronic projects hobbies and repairs, in radios powers supplies and other devices.
Technical data
- 2W10 Data: Forward rectified current:2A,Maximum recurrent peak reverse voltage:1000V
- Feature:Low Reverse Leakage Current /Low Power Loss/ High Efficiency
- Lead-Free / RoHS Compliant Electronics Component / Through Hole
- Terminals: Plated Leads Solderable per MIL-STD-202, Method 208
- Polarity: Symbols Marked on product
• Solderless breadboard (MB-102)
• Wire size: Suitable for 29-20 AWG wires
• Size: 16.5 x 5.5 x 0.85 cm
• Double sided tape on bottom. Can be fixed on a flat surface
• Solderless breadboard (GL-12)
• Wire size: Suitable for 29-20 AWG wires
• Size: 175 x 67 x 8 mm
• Double sided tape on bottom. Can be fixed on a flat surface
Breadboard /Project Board
- Ultra low cost
- 3 to 5V power and I/O
- 2.5mA max current use during conversion (while requesting data)
- Good for 20-80% humidity readings with 5% accuracy
- Good for 0-50°C temperature readings ±2°C accuracy
- No more than 1 Hz sampling rate (once every second)
- Body size 15.5mm x 12mm x 5.5mm
- 4 pins with 0.1" spacing
SCT-013 100 A
Non-Invasive AC Current Sensor Split Core Type Clamp Meter Sensor. SCT-013-000 is a Non-Invasive AC current sensor i.e. it is a current transformer which can be used to measure AC current up to 100 amperes.
Current transformers(CTs) are sensors are for measuring alternating current. They are particularly useful for measuring whole building electricity consumption (or generation for that matter). The split core type such as the SCT-013-000 in the picture is particularly suitable for DIY use. Clip this SCT 013 000 straight on to either the live or neutral wire coming into the building without having to do any high voltage electrical work.
This is a current output , you can add a burden resistor to measure voltage across
Package Includes :
1 x 100A AC Current Sensor Module.
Arduino Example
https://learn.openenergymonitor.org/electricity-monitoring/ct-sensors/how-to-build-an-arduino-energy-monitor-measuring-current-only?redirected=true
Float level switch is a simple structure, easy to use level
control device, it does not provide power, no complicated
circuit, it has a mechanical switch than the average small
size, long life and other advantages. As long as the material
used in the correct shape and nature of any liquid or
pressure, temperature can be used, which in the
shipbuilding industry, generating equipment, petrochemical
industry, food industry, water treatment equipment, dyeing
and finishing industry, hydraulic machinery, etc. have been
widely application.
How it works: liquid level sensor magnetic reed switch by
having an important and
integral float, float within the magnetic material in a sealed
non-magnetic metal pipe or plastic pipe set one or more
magnetic reed switch, and then the catheter through a or
more with magnetic float, and double-loop control using a
fixed float and reed
switch in the relevant position, the float rises or falls with
the liquid using the ball close to the beginning of the reed
contacts, resulting in open and shut action for level control
or direction (when the float near the reed switch is turned
on; leave the switch off)
Max Contact Rating :10W
Max Switching Voltage:220V
Max Switching Current:0.5A
Max Breakdown Voltage:220VDC
Max Carry Current:1.0A
Max Contact Resistance:100mohm
Temperature Rating:-10~+60°
Float Ball Material:P.P
Float Body Matertal:P.P
Single Phase Dc-Ac State Relay Ssr-40Da 40A Input 3-32V Dc Output 24-380V Ac
1 CH DC 5V Relay Module without Optocoupler isolation 5V Level Trigger
