Microcontrollers & Acc
- Ultra low cost
- 3 to 5V power and I/O
- 2.5mA max current use during conversion (while requesting data)
- Good for 20-80% humidity readings with 5% accuracy
- Good for 0-50°C temperature readings ±2°C accuracy
- No more than 1 Hz sampling rate (once every second)
- Body size 15.5mm x 12mm x 5.5mm
- 4 pins with 0.1" spacing
Supports the reduced pin count RMII interface
Supports HP Auto-MDIX
Supports single 3.3V supply
Onboard chip package: 24-pin QFN (4x4 mm) Lead-Free RoHS Compliant package
Flexible Power Management Architecture
Integrated 1.2V regulator
I/O voltage range: +1.6V to +3.6V
Size approx 25.8 x 49.2 mm
WIFI NodeM ESP8266+32Mb, module is based on widely explored esp8266 System on Chip from Expressif.
WIFI NodeM ESP8266+32Mb, compatible for NodeMCU board. We add extra memory size to 32Mb. This better, for make big project with big library. You not need to worry about size of memory.
On board have USB-TTL serial converter CH340G, with Micro-USB socket.
PowerIn for DC 5~9V, to pin VIN.
Pin headers 2.54mm (0.1") 15 pins x 2 lines in set.
It combined features of WIFI accesspoint and station + microcontroller and uses simple LUA based programming language.
WIFI NodeM ESP8266+32Mb, offer:
Arduin0-like hardware IO. And can programming in Arduin0 IDE
Event-driven API for network applicaitons
10 GPIOs D0-D10, PWM functionality, IIC and SPI communicaiton, 1-Wire and ADC A0 etc. all in one board
Wifi networking
Operating supply voltage 2.5 V to 6 V
The PCF8574 IO Expansion Board is used as remote 8-bit I/O expander for I2C-bus. Up to 8 PCF8574 IO Expansion Board can be connected to the I2C-bus, providing up to 64 I/O ports.
PCF8574, I2C interface, 8-bit parallel port.
For the lack of I / O resources mcu to I / O expansion.
Supports two types of access to the target board interface: pin or row.
Supports I2C bus cascade (via pencil row docking methods used simultaneously several I2C modules).
Description:
If your IO port is not enough, you can use the PCF8575 expansion board to expand more IO ports. Only two wires are needed. SDA and SCL can realize the input and output control of 16 IO ports, which is very simple to use. The I2C signal can be simulated by software, and some microcontrollers with I2C interface can operate directly.
Description:-
Arduino Mega Sensor Expansion Board Shield allows you to connect to various modules like sensors, servos, relays, buttons, potentiometers.This mega sensor shield v2.0 allows you to hoop up the sensors directly to Arduino mega (2560) or Arduino mega(ADK) without the use of the breadboard. it also expand the mega with Bluetooth module communication interface ,SD card module communication interface, APC220 radio-frequency module communication interface, RB URF v1.1 ultrasonic sensor interface and ICSP interface. easy to use for extension.
Features:
- PIN13 Stat Power LED indicator
- Digital IO Ports D0-D53
- Analog IO Ports A0-A15
- Reset Button up to top
- External Power In
- SD Card Interface
- Ultrasonic Interface
- ISP Interface
- Bluetooth Interface
- APC220 Interface
- Dimension:53.5mm * 100mm
* Product Images are shown for illustrative purposes only and may differ from actual product.
RTC real-time clock module DS3231SN ChronoDot V2.0 I2C
Oporating Voltage 5.0 V DC.
Battery type required CR1220 battery
The DS3231 has an internal crystal and a switched bank of tuning capacitors. The temperature of the crystal is continuously monitored, and the capacitors are adjusted to maintain a stable frequency. Other RTC solutions may drift minutes per month, especially in extreme temperature ranges...the ChronoDot will drift less than a minute per year. This makes the ChronoDot very well suited for time critical applications that cannot be regularly synchronized to an external clock.
The ChronoDot will plug into a standard solderless breadboard and also has mounting holes for chassis installation.
The I2C interface is very straightforward and virtually identical to the register address, which means that existing code for the Arduino, Basic Stamp, Cubloc, and other controllers should work with no modification.
** Does not include battery
Description
This module features the adjustable LM2596 step-down (buck) switching regulator, capable of driving a 3A load with excellent line and load regulation.
This module has a multi-turn trimpot (potentiometer) that you can use to adjust the LM2596's output voltage. Since the trimpot has 25 turns of adjustment you can easily adjust the output of the module to exactly the voltage you need.
The simplest way to reduce the voltage of a DC supply voltage is to use a linear voltage regulator (LDO), but linear regulators step down voltage by dissipating the excess energy as heat and do not yield any current step up. on the other hand, can be remarkably efficient and provide a step up in current output. Buck converters are one of the best ways to provide a regulated voltage from a battery since they don't waste near as much energy in the process of dropping the input voltage as a linear regulator would waste.
Specifications:Input Voltage 3 to 40 V Output Voltage Range 1.23 to 37 V Max Output Current 3 A Adjustment 25-Turn Trimpot Efficiency up to ~93% Switching Frequency 150 kHz Built-In Protection thermal shutdown and current limit Dimensions: Length 43.2 mm (1.701") Width 21 mm (0.827") Height 14 mm (0.551") Weight 11.23 g (0.396 oz)
1.AD8232 adopts double poles high-pass filter to eliminate the motion artifacts and electrode half cell potential
2.AD8232 adopts an operational amplifier that is without using constraint to build a three pole low pass filter, eliminating extra noises
- Rated temp range : 0----70degree
- Working temp range: -40-----85degree
2. The port type: I2C
3. Working voltage: 1.8 - 6.0V
4. Interface size: 4*2.54mm spacing
5. The humidity precision: typical ± 2%
6. Humidity resolution: 0.024%
7. Temperature accuracy: typical ± 0.3 °c
8. Temperature resolution: typical 0.01 °c
9. The operating temperature: -40 ℃-85 ℃
INMP441 Omnidirectional Microphone Module MEMS I2S Interface Supports ESP32
INMP441 is a high performance, low power consumption, digital output, omnidirectional MEMS microphone with bottom port. The
The complete INMP441 solution consists of a MEMS sensor, signal composition conditioning, analog-to-digital converter, anti-aliasing filter, power management and industry standard 24-bit I2S interface. The I2S interface allows INMP441 to connect directly to digital processors, such as DSPs and microcontrollers, without the need for the audio codec used in the system. INMP441 has a high signal-to-noise ratio and is an excellent choice for near-field applications. INMP441 has a flat broadband frequency response, resulting in high definition of natural sound.
Product Features:
1. Digital I2S interface with high-precision 24-bit data
2. High signal-to-noise ratio of 61 dBA
3. High sensitivity -26 dBFS
4. Stable frequency response from 60 Hz to 15 kHz
5. Low power consumption: low current consumption of 1.4 mA
6. High PSR: -75 dBFS
1. It supports Micro SD card,Micro SDHC card
2. Communication interface is a standard interface
3. 4 M2 screw positioning hole, easy to install
4. Power supply:4.5-5.5V
5. Current:0.2-200mA
6. Interface level：3.3 or 5v
7. Cards Supported: Micro SD card(<=2G)，
Mirco SDHC card(<=32G)
8. Size：42X24X12mm
Low power consumption - 0.5uA at 1Hz
I2C interface
Max I2C Speed: 3.5Mhz
Very low noise - up to 0.02hPa (17cm)
Full calibrated
Pressure Range: 300hPa to 1100hPa (+9000m to -500m)
Module model: GY-6500
Using the chip: MPU-6500
Power supply: 3-5v (internal low dropout voltage regulation)
Communication method: standard IIC/SPI communication protocol
Chip built-in 16bit AD converter, 16-bit data output
Gyro range: ±250 500 1000 2000 °/s
Acceleration range: ±2±4±8±16g
Adopting Shenjin PCB, the machine welding process guarantees the quality
Pin pitch 2.54mm
Module size 15mm*25mm
Specifications
Operating Voltage: 5V
Input Voltage (Recommended): 7-12V
Power 5V: Provided through USB Type-B Port
Power External: Through 2.1mm barrel jack (7v to 12v DC)
Digital I/O Pins: 14 (of which 6 provide PWM output)
Digital I/O: 3.3v Logic Levels
PWM Digital I/O Pins: 6
Analog Input Pins: 6 (3.3v Logic Levels)
ISP Programming: Available through TX/RX ports
DC Current per I/O Pin: 20 mA
DC Current for 3.3V Pin: 50 mA
Flash Memory: 32 KB
SRAM: 2 KB
EEPROM: 1KB
Clock Speed: 16 Mhz Oscillator
Considerations
ATmega328P devices use 3.3v logic levels, unlike other devices which may use 5v logic levels. For this reason, when interfacing to other devices which will drive your Wavgat Arduino Uno R3 board. A simple voltage divider circuit is all that is required.
https://www.pcboard.ca/arduino-uno-r3-wavgat-setup
The board has heater and fan MOSFET outputs and 3 thermistor interfaces.
The LED will light when the heater has output.
Heated bed has additional 11A fuses.
Two Z motor outputs available incase you want to connect..
Jumper included to configure the steps of your driver board
1.3″ I2C OLED Display
This 1.3″ I2C OLED Display is an OLED monochrome 128×64 dot matrix display module with I2C Interface. It is perfect when you need an ultra-small display. Comparing to LCD, OLED screens are way more competitive, which has a number of advantages such as high brightness, self-emission, high contrast ratio, slim outline, wide viewing angle, wide temperature range, and low power consumption. It is compatible with any 3.3V-5V microcontroller, such as Arduino.
Features:
- Interface: I2C
- Driver chip: SSH1106
- Diagonal Screen Size：1.3″
- Voltage: 3.3-5V
- Number of Pixels: 128 x 64
- Color Depth: Monochrome (Blue)
- Working temperature:-40-70 degree
- Dimension: 33.5 x 36 x 4.3 mm