Discrete Electronics
Longruner LKY62/MG996R Metal Gear Torque Digital Servo Motor
MG996R Metal Gear Digital High Torque Servo 55g
Description:
This is essentially an upgraded version of the famous MG995 servo. It now has a redesigned PCB and IC control system which makes it more accurate. Its internal gearing and motor are also upgraded to improve dead centering.
All specifications are the same as the previous model MG995, however this servo is far more accurate, and safe to use in aircraft which require precise servo movements and perfect centering.
Specification:
Item Name: MG996R
Weight: 55g
Dimension: 40.7*19.7*42.9mm
Stall Torque: 10kg/cm
Operating Speed: 0.20sec/60degree(4.8v)
Operating Voltage: 4.8-7.2V
Temperature Range: 0°C - 55°C
Servo Plug: JR (Fits JR and for Futaba)
Package Included:
1x MG996R servo
Mounting Screw and arms
MT3608 2A DC-DC Step Up Power Module
The MT3608 2A Max DC-DC Step Up Power Module Booster Power Module is a low-cost module that can step-up a 2 to 24V input voltage up to a 5 to 28V output at up to 2A peek.
DC-DC boost converters step up the input voltage to a higher voltage while also stepping down the available current since the module can’t output more power than its inputs.
This boost converter is adjustable and capable of outputting a voltage in the range of 5.0 to 28V at a continuous current of up to 1.5A depending on input/output voltage settings with 1A available with most settings.
Since it is a boost converter, the input voltage must be lower than the output voltage.
The device is able to use low ESR bulk ceramic capacitors rather than electrolytic caps which avoids long-term aging concerns and contributes to the compact packaging.
The MT3608 converter IC has over-current and thermal limiting features built-in to safely shut the device down if driven too hard.
Voltage Adjustment:
The module has a single-turn potentiometer for adjustment of the output voltage.
Turning the pot CW decreases the output voltage while turning it CCW increases the output voltage.
The upper limit of the adjustment range will depend on the input voltage and the load. With a 9V input for instance, at 1A, the upper voltage limit will be approximately 20V.
Module Connections
These are compact boards with 4 solder pads for making connections.
- VIN+ = Input Voltage
- VIN- = Ground
- VOUT+ = Output Voltage
- VOUT- = Ground. Connected to VIN- on the module.
Description:
Charge module - Linear charging.
It has TYPE-C USB female
It still retain the input voltage wiring solder joints, can be very convenient to DIY
Specifications:
Current- 1A adjustable.
Charge precision- 1.5%.
Input voltage- 4.5V-5.5V.
Full charge voltage- 4.2V.
Led indicator- red is charging green is full charged.
Input interface- micro USB.
Work temperature- -10℃ to +85℃.
Inverted polarity- NO.
Size: 27mm X 17mm.
1 x 18650 batteries (6000 mAh) you can charge with this charger in parallel at the same time
Operation Manual:
1. Type-c female base and the power input end of + ~ welding pad position next to it, connect to 5V input voltage.
2. B+ is connected to the positive electrode of lithium battery, and B~ is connected to the negative electrode of lithium battery. OUT+ OUT connect loads, such as set-up board.
3. Connect the battery to B+ B-, insert the phone charger to USB, the blue light is on, indicating that there is a power supply, the red light flashes, indicating that it is charging. When the charge is full, the red light stops flashing and turns into a regular light.
4. OUT+ OUT- terminated can be load. After load on, the red light is always on. When there is a power supply at the input end, obtain current from the output end of the power supply. If there is no power supply, obtain current from the battery. When the battery voltage is lower than 2.5v, automatically close the output.
Only one 18650 batteries (6000 mAh) you can charge with this charger in parallel at the same time
Features:
1, Transmission signal processing control chip RCWL-9196
2, Wide operating voltage range: 4.0-28.0V
3, Compared with the traditional infrared feeling PIR, with the penetrating detection capability
4, Block time, distance adjustable
5, Output 3.3V power supply
6, Board size: 35.9mmx17.3mm
Application Design Note:
1, the sensing face in front of the gold without any shelter.
2, front and rear sensing surface space to set aside more than 1CM
3, the module carrier plane and install as flat line
4, a certain application of effective detection area
5, the component side of the module is positive sensing face, the opposite is negative sensing surface. Negative sensing surface sensing less effective
6, microwave modules can not be large-scale applications in the same area, otherwise there will be mutual interference. Between single individuals over distance greater than 1M
7.RPM 500
7.RPM 500
LDR ( light Dependent Resistor)
Photosensitive resistor 5528 5MM
Solenoid valve with integrated water input filter mesh 12V DC
Features :
- Durable and practical.
- Made of high-quality plastic and metal, long life.
- Very convenient to use, open or close when power on or off.
Specification :
- Material: Metal + Plastic
- Voltage: DC12V
- Rated Power: 5W
- Pressure: 0- 0.8Mpa
- Interface Modes: 1'' Hose
- Working Time: 5hours at once (Max)
Insulation Class "E":
- Fluid Temperature: 0-90℃
- The inner diameter: 20mm/0.78''
- Four external diameter of thread: 25mm/1''
- Switch power supply, convert AC 110V/220V to DC 12V 30A 360W.
- Dual input voltage: AC 110V/220V. There is a switch, choose the proper voltage before use.
- Protection: Shortage Protection, Overload Protection, Over-voltage Protection:115%-135%,Action output cut-off Reset:Auto Reset or fuse.
- Smart device surge protection for Shortage Protection, Overload Protection, Over Voltage Protection
- Wide input voltage range, steady and precise output voltage.Great power transformer for electronic equipment, Led Lighting, home appliance etc.
Solenoid valve with integrated water input filter mesh 12V DC
Features :
- Durable and practical.
- Made of high-quality plastic and metal, long life.
- Very convenient to use, open or close when power on or off.
Specification :
- Material: Metal + Plastic
- Voltage: DC12V
- Rated Power: 5W
- Pressure: 0- 0.8Mpa
- Interface Modes: 1/2'' Hose
- Working Time: 5hours at once (Max)
Insulation Class "E":
- Fluid Temperature: 0-90℃
- Size: L x W x H/80 x 35 x 55mm/3.14 x 1.37 x 2.16''
- The inner diameter: 14mm/0.55''
- Four external diameter of thread: 20mm/0.78''